Top 10 usual forklift accidents ， forklift operation must focus on these matters ！.

Don't ignore the forklift at the workplace. If the operation is bad, there will be significant mishaps in minutes, and there are several accidents involving forklifts.

Situation 1: The forklift cargo blocked the chauffeur's view, and the individual ahead can not be located, causing a rolling crash.
Instance 2: In order to preserve the balance of the forklift when raising hefty goods, the workers used their body weight as the weight, which practically triggered casualties.
Case 3: The width of the forklift freight exceeds the allowable width of the course and hangs on the roadside rack, which practically causes an mishap.
Instance 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not notice the pedestrian, and the pedestrian did not observe the forklift.
Case 6: The forklift raises the workers unlawfully, the forklift driver does not wear the seat belt, the forklift lifter falls and the chauffeur is crushed when the forklift surrender.
Case 7: The forklift chauffeur did not put on a safety belt and fell from the automobile when it surrendered and was crushed.
Forklift operation must focus on these issues ：.

Beginning.
1. Before beginning, observe the surroundings, and after confirming that there are no challenges that impede the safety and security of driving, beep the horn initially and afterwards start.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic stress ( atmospheric pressure) scale need to be risk-free prior to beginning.
3. When the forklift starts with a lots, the vehicle driver must first verify that the tons is steady and dependable.
4. The begin should be slow-moving and stable.

Driving.
1. When driving, the height between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast must be tilted backwards. .
2. Do not lift the fork too expensive when driving. When going into and leaving the task site or while driving, beware that there will be no challenges in the sky. When the load is traveling, the fork must not be increased too expensive, which will certainly affect the security of the forklift. .
3. After discharging, the fork must be reduced to the regular driving position before driving. .
4. When turning, if there are pedestrians or lorries nearby, the driving signal should be provided first. High-speed doglegs are forbidden. High-speed sharp turns will certainly cause the lorry to lose side security and tip over. .
5. When the forklift is downhill, it is strictly prohibited to switch off the flame and slide, and it is prohibited to brake instantly while driving with lots unless there are unique scenarios.
6. When the forklift is running, it needs to comply with the website traffic rules in the manufacturing facility and should maintain a specific security distance from the vehicle ahead. .
7. When the forklift is running, the tons must remain in the lowest placement that does not impede the driving, and the gantry must be effectively slanted back. The load will not be increased other than when piling or filling. .
8. The height of the load have to not block the vehicle driver's view. In unique circumstances, when the item impacts the forward vision, drive at a reduced speed when reversing.
9. It is prohibited to activate the ramp, nor to drive across the ramp. .
10. The secure driving speed of the forklift in the factory location is 5 km/h, and it has to drive safely at a low rate when entering the manufacturing workshop area. .
11. When the forklift is raised, lifted or driven, it is restricted for employees to depend on the fork to hold things and play a stabilizing function. .
12. If problems are located, they will be fixed and reported in a timely way, and they will certainly never operate with illnesses or conceal them.

filling and dumping.
1. When fork-loading items, the distance between both forks ought to be adjusted as needed to make the load of both forks balanced and not manipulated, and one side of the thing must be against the shelf. .
2. It is forbidden to work with a solitary fork or utilize a fork top or draw. In unique scenarios, safety and security indication need to be established to remind bordering pedestrians. .
3. In the process of packing and discharging products, the forklift should be braked with the brake. .
4. The speed of the lorry need to be slow-moving and consistent. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled things and harm people. .
5. When making use of a fork to fork the goods, the fork must be as deep as possible under the tons, and it ought to be kept in mind that the fork suggestion should not touch various other products or items. The tons ought to be stabilized with marginal back tilt of the gantry so that the load does not glide backwards. The pole can be tilted onward somewhat when the lots is lowered to enable easy placement of the load and extraction of the forks. .
6. It is forbidden to fork products at broadband and ram difficult objects with the fork head. .
7. When the forklift is functioning, it is restricted for individuals to loaf the fork, so regarding avoid the collapse of the goods and injure people. .
8. Overloading is restricted, and it is prohibited to use forks to raise employees to participate in high-altitude operations to stay clear of high-altitude falling crashes. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll objects. .
10. It is not allowed to use forks to select, turn pallet unload.

Leaving .
1. It is restricted to leave the forklift when the things on the fork are in the air. Before leaving the forklift, you must dump the goods or lower the fork frame.
2. Pull the hand brake handle to dead or depress the hand brake switch.
3. The engine is switched off and the power is removed. (Except for special conditions, such as the chauffeur does not leave the vehicle's view and does not exceed 1 min).
4. Remove the secret. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the look ought to be examined, and fuel, lubing oil and air conditioning water ought to be included.
2. Inspect the security efficiency of starting, running and stopping.
3. Examine whether the lights and horn signals are complete and efficient.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature level are normal.
5. After the forklift is running, the outside leakage must additionally be examined and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You need to examine prior to leaving the auto;.
2. When you experience someone before you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the nadir of the cargo ought to be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be too sharp to avoid the tendency of "free switching";.
6. Adding and down the slope needs to be sluggish and consistent, and no turning on the incline is enabled.
7. Do not drive across the gradient. When the slope is more than 10%, the automobile must be driven backwards when going downhill;.
8. When the forklift workers bring the goods and move on, if they encounter big or hefty items and go to the chauffeur's line of sight, they need to take the turning around exercise
.
The "Eight Prohibitions" ought to be followed in the procedure.
1. Single fork operation is not enabled.
2. It is not enabled to raise the goods for cross country driving.
3. Electric Forklift Truck for Warehouse It is not allowed to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not allowed to use inertia force to grab the goods.
6. It is not enabled to use stopping pressure to expatriation round or easy-to-roll items.
7. It is not allowed to bring individuals to service the pallet or fork, and it is strictly restricted to stand under the fork after the fork is elevated.
8. Do not drive laterally on inclines
.
Parking is not allowed under the following problems.
1. Curves, narrow roads, Stand-on Electric Pallet Stacker railway crossings;.
2. Sections with a longitudinal incline higher than 5%.
3. When there is an challenge on one side of the roadway, the opposite side of the section with the very same length as the challenge should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844